Having two powerful routers will allow you to enjoy good performance across the network. Additionally, if you opt for dual-band routers, you will be able to significantly reduce the impact of the second transmission or hop. Just use one frequency band for the bridge and the other one for your devices. Your email address will not be published. Wireless Client This mode lets you connect the router to another router in client mode. Access Point This mode is suitable for establishing a basic wireless access point.
Downsides of a wireless bridge The main issue with using a wireless bridge in repeater mode and WDS mode is that slower speeds can be expected. Renee Biana December 11, 0 4 minutes read. Related Articles. Best apps to encrypt your files before uploading them to the cloud August 14, Best alternatives to Popcorn Time February 12, Leave a Reply Cancel reply Your email address will not be published.
Check Also. See below for details about that setting. CTS is typically used for Disabled is the recommended setting, since well-designed networks rarely need it. However, if you are experiencing lots of physical layer collisions, then you might try enabling this and tuning the RTS Threshold setting.
This option lets you choose which wireless standards are followed. Countries usually adjoining that share a common set of regulations are referred to in the Four major regulatory bodies have authority over almost all of the world's technology regulations:.
Each domain has strict regulations for parameters such as antenna gain, transmit power, channel selection.
Many countries choose to adhere to the standards completely. A few countries modify an existing standard to their own unique needs. This can create complications. It solves problems like interference with satellites and radar using the same 5 GHz frequency band. Media Access Control layer. Country code AND rev ision define the possible channel list, power and other regulations for each country. The current wireless driver year and newer supports approximately countries and combinations of country code and revision.
Some combinations of Country and revision codes are invalid, and will not work together. Most users will be able to choose the correct settings from those in the Wireless menu.
However, there are many more settings. There, you will see the following:. The comment field on the right contains valid country and revision combinations. They are special values for testing and not for regular use. This applies to release and later. Revision settings only exist in FreshTomato and later.
Bluetooth and 2. Choosing Enable can help to reduce that interference, by asking the Bluetooth devices to take turns using the same channels as your Wi-Fi. The Preemptive function will make FreshTomato inform the Bluetooth device about which Bluetooth channel it's operating on.
The Bluetooth devices must support the Bluetooth Coexistence function, or they will be unable to share nicely and this option will have no effect. When a router sends a packet to a client, it waits for an ACKnowledgement frame from the client to ensure the packet was received. Traditionally, ACK Timing is set to the maximum distance of the furthest client device in meters x 2.
For example, if you roam with your laptop up to 50 meters from your AP, the setting would be Generally, the default is recommended, except where administrators have a strong knowledge of timing or are building long-distance wireless links. Typically, Therefore, one might assume this should never be set higher than However, in scenarios with high power antennas or other long-range gear, the timing settings would need to increase.
Longer distance links have been established far beyond the theoretical limits of However, higher ACK Timing comes at the cost of lower throughput. If set too high, packets could be lost as the router waits for the ACK window to timeout for ACK frames that were never going to arrive.
This too might lower throughput. When in power-save mode, a client device may sleep for one or more beacon intervals, then wake up for beacon frames that include DTIMs.
A DTIM message notifies sleeping clients that they will need to wake up to receive the waiting frames. DTIM Interval values range 1 to This means that the DTIM message is included in every second beacon frame. In other words, wireless clients may have conflicting requirements for power consumption and communication throughput when in power-save mode. IP fragmentation is the process of the IP layer breaking down datagrams into smaller pieces fragments.
The destination host, or sometimes intermediate routers reassemble the fragmented pieces to make the message whole again. This is usually done to reduce the size of the datagrams so that the pieces can pass through a link with a smaller MTU than the original datagram size.
This option specifies the maximum size of datagram that can occur before it is fragmented into multiple datagrams. Too low values may cause poor network performance. The default setting is reccomended. Frame-bursting is a link layer protocol used to increase the throughput of connections on links between It does this by reducing the overhead used in the wireless session between hosts. It grew from standards first introduced in the Network protocols for shared media are designed so that any host that has sent a MAC layer frame is then supposed to yield the medium and wait for a fixed period of time.
This helps create a fair use of the medium by multiple users. As usual, there are compromises. Frame Burst can cause unfair allocation of airtime on networks where where only some clients support Frame Burst.
The wait periods between frames were not originally designed to include data traffic. The recommended setting is Disabled, unless there are very few hosts on your network. In other words, suppose the host router is at A client at At the risk of sounding redundant, wireless Ethernet bridge mode is just like wireless client mode, except that the client is bridged to the host. In bridged mode, your clients think they are connected directly to the host router.
They receive their IP addresses from the host router. The client router is a transparent intermediary. Setting up bridge mode is very similar to wireless client mode. You could set it to 0. If you control the primary router, you should know which IP addresses are inside the DHCP pool, and choose one outside that pool. In the above example, the host router is at As with setting up wireless client mode, you next configure SSID, Channel, and Security to match the primary router see wireless client mode section above for more detail.
Tomato will restart. If a standard renewal does not work, you may need to disable and re-enable your Ethernet adapter I had to do this in XP. Running your router as a client is one of the neater things you can do with alternative firmware, such as Tomato, and is rarely if ever supported in official stock firmware.
Save my name, email, and website in this browser for the next time I comment. Client mode, two ways In fact, Tomato supports two types of client modes: wireless client mode and wireless Ethernet bridge mode. Wireless client mode Step 1—Find the network name and parameters of your primary router When we configure Tomato in client mode, it needs to know information about the wireless network we are connecting to.
0コメント